Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Installation for Pittsburgh Homeowners
Most gate installation problems in Pittsburgh start before the first post goes in. A sloped driveway off a hillside street gets a gate sized for flat ground, an operator picked from a catalog without checking the swing, and by winter the thing binds, drifts, or quits halfway. We’re a gate specialist, not a fence crew that also wires operators. Our technicians have up to 14 years of experience, and every job starts with measuring the actual opening and the actual grade before we spec anything. We handle the install and the repair side of the same system, so you’re not hunting for a second contractor when a board or a hinge needs attention. Installation is scheduled work, not same-day, but we do quote it free and in writing. Call (866) 361-7838 to get a measure on the books. We answer 24/7.
Automatic Gate Installation
Automatic Gate Installation means the gate opens and closes on its own, driven by an operator wired to a control board and triggered by a remote, keypad, or loop detector. You need it when a manual gate has become a daily chore, when a property needs controlled entry, or when an existing automatic system is old enough that the operator no longer matches the gate. We measure the opening, confirm the power source, and match the operator to the gate’s weight and travel rather than to whatever’s on sale. Installation pricing is set per job by a written estimate after we’ve seen the site. A residential swing or slide system commonly lands between $2,800 and $6,500 with the operator, and commercial systems run higher based on duty cycle and access control.
Matching Operator to Gate
An operator sized wrong for the gate is the most common reason an automatic system fails early. We weigh the leaf, check its travel, and look at how much wind load the site actually gets before picking a unit. That’s the difference between a system that runs for years and one that strains from the first cold snap.
Power and Control Planning
Automatic gate work lives or dies on the electrical side. We plan where the power run lands, where the control enclosure sits, and how the safety edges and photo eyes get wired before anything is mounted. Sorting that on paper first saves a second visit later.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Gate Installation Services
Gate Installation Services cover the full job: setting posts or mounting hardware, hanging the gate, fitting the operator, and commissioning the controls so the system works as one piece. You need this when you’re starting from nothing, replacing a gate that’s failed beyond repair, or changing the entry layout on a property. We quote the whole scope in one written estimate so there’s no gap between the hardware and the electronics that someone else has to fill. Because we also handle gate repair Pittsburgh work, we build installs with the service side in mind: accessible boards, sensible wiring, parts you can actually get to. Residential gate installation typically runs $1,800 to $5,500 depending on the gate type and operator, with the final figure set by the written estimate.
Single-Scope Estimating
One estimate covers the gate, the operator, the controls, and the commissioning. Nothing gets split off to a second trade, so the price you agree to is the price for a working system. We walk the scope with you before any work starts.
Residential and Commercial Fit
Homeowners usually want a driveway gate that opens reliably and looks right from the street. Property managers want controlled entry, audit trails, and a system that won’t lock out residents. We write the scope to fit whichever one you are.
Electric Gate Installation
Electric Gate Installation is the wiring and control side of the job, the part that turns a gate into an entry system: the power feed, the control board, the keypad and remote receivers, the loop detectors, and the safety devices. You need it whenever an entry has to be managed rather than just opened, or when a manual gate is being automated and the electrical side has never existed. This is where a lot of single-trade contractors stop, and it’s where we start. We work on FAAC and BFT systems specifically because commercial entry depends on that layer being right. Electrical scope is priced per job in the written estimate, and a typical electric gate install with access control runs $3,500 to $8,000 depending on the number of entry points and devices.
Access Control Devices
Keypads, remotes, intercoms, and loop detectors each need their own wiring and their own place on the board. We plan the device list before the trench gets dug so nothing has to be retrofitted later. A gate that opens but can’t be controlled isn’t finished.
Safety Devices First
Photo eyes and safety edges are what stop a closing gate on a person, a car, or a pet. We treat them as required equipment, not an upgrade, and we test them at commissioning. On any electric gate, the wiring and the safety edges are a job for a trained professional, not a homeowner project.
Driveway Gate Installation
Driveway Gate Installation is a gate built around how a specific driveway actually works: its width, its slope, its turning room, and where a vehicle stops to open it. You need it when a driveway has no controlled entry, when the current gate is too narrow or hung wrong, or when you’re laying out a new drive and want the gate figured into the plan instead of added after. Pittsburgh driveways are rarely flat, and grade changes drive every decision after that. We measure the slope, check clearances, and set the posts to proper footing depth for the gate and operator weight. A driveway gate install typically runs $2,200 to $6,000 depending on width, material, and whether an operator is included. The estimate is free and the number is fixed in writing before we start.
Slope and Swing Clearance
A gate that clears level ground can drag on a slope, and a swing gate on a hill needs room to travel without clipping a retaining wall or a parked car. We check the arc before a hinge gets set. Getting this wrong is what makes a gate annoying for the life of the install.
Footing Depth and Posts
Posts carry everything above them, so they go to proper footing depth for the gate size and the operator. We set them to hold against the frost heave and soil movement that comes with a Pittsburgh winter. A gate that leans by spring was under-built in the fall.
Sliding Gate Installation
Sliding Gate Installation is the right answer when a driveway has no room for a swing but plenty of room along a fence line or a wall. It’s also what you want on a wide opening, a commercial entrance, or a property where vehicles queue close to the gate. You need it when the opening is too wide for a swing gate, when the ground slopes across the gate line, or when traffic flow at an entry has to keep moving. We lay out the track and the cantilever, set the posts to proper footing depth, and match the operator to the gate’s weight and travel speed. Sliding gate installs typically run $3,000 to $7,500 depending on width, drive type, and operator. Pricing is per job by written estimate, agreed before any work begins.
Cantilever Versus Tracked
A cantilever gate rolls without a ground track, which matters where a driveway crosses the gate line and a track would get driven over. A tracked gate is simpler and cheaper but needs the ground kept clear. We’ll tell you which fits your site and why.
Operator Travel and Speed
Sliding operators are matched to weight and to how fast the gate has to clear an opening. A heavyweight gate on an undersized operator will wear out its gearbox long before its time. We size the operator for the gate, not the other way around.
Gate Opener Installation
Gate Opener Installation is fitting the motor and control unit that drives an existing or new gate and making the whole thing respond to remotes, keypads, and sensors. You need it when a manual gate is getting automated, when a failed operator on an otherwise sound gate needs replacing, or when a property changes hands and the entry system has to be brought up to a working standard. We work on Linear, Viking, and other operators and know where each one tends to wear. A gate opener install typically runs $1,400 to $4,000 depending on the operator class and the access devices. The estimate is free, the price is quoted before work begins, and any operator we fit gets commissioned and tested before we call it done.
Control Boards and Receivers
The board is where every device on the gate lands: remotes, keypad, loop, photo eyes. We map each input before wiring so the finished system is easy to service. A board that’s a rat’s nest on day one is a service visit on day two.
Test Cycles at Commissioning
Every new operator gets a full cycle test with the safety devices live, and we check force and travel against the gate’s actual weight. If the gate binds at any point in the run, we find it now. That’s how we avoid a repeat visit.
Gate Fabrication
Gate Fabrication is building a gate for an opening that no stock size fits: a custom driveway width, a slope that rules out a standard leaf, or a design requirement a property has to meet. You need it when an off-the-shelf gate would be hung with fills and gaps, or when a property and its access need a one-off piece. We fabricate to the measured opening, then hang and commission the gate ourselves, so fabrication and install aren’t two separate contractors pointing at each other. Because we specialize in gates only, the fabrication is built around how the gate will actually be operated, not just how it looks. Custom fabrication typically runs $2,500 to $8,000 or more depending on size, material, and finish, quoted per job in a written estimate after we’ve measured.
Material and Design Choices
Steel, aluminum, and wood each behave differently in a Pittsburgh climate, and each holds up to an operator differently. We’ll talk through weight, finish, and settling before anything gets cut. The gate has to survive wind, snow, and a freeze-thaw cycle, not just the photos.
Built for the Operator
A custom gate has to be built with the operator in mind from the first weld. Hinge points, leaf balance, and the mounting boss for the operator all get planned in. A gate built for looks and retrofitted for a motor rarely works as well as one designed as a system.
Brands We Service
We work on a set of operators we know well, and that knowledge is what shortens a diagnosis. On FAAC systems we know the boards and the actuators that give trouble first, and we go straight there instead of working through the manual. BFT systems are commercial-grade and often sit on properties where downtime matters, so we come in already familiar with the control architecture. On Linear and Viking we know how the residential and light-commercial operators wear, and where a failing component shows up before it stops the gate.
LiftMaster, Ghost Controls, DoorKing, Elite, and Mighty Mule are the rest of the set, and each one gets the same brand-specific approach: know the failure pattern, check the likely part first, fix the root cause instead of the symptom. Whether you have FAAC, BFT, or any other make, we can help. Call (866) 361-7838 and tell us the brand and the symptom, and we’ll book an install or a Pittsburgh gate repair visit that fits.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- The gate has started hitting the ground or the frame. That’s usually a post settling or a hinge wearing out. Left alone, the gate racks itself out of square and the repair gets bigger.
- The operator cycles but the gate barely moves. A strained operator points to weight, travel, or a worn drive before it points to the motor. Running it that way burns the gearbox.
- Safety edges or photo eyes aren’t stopping the gate. A gate that closes without a working safety device is a hazard on any driveway. Stop using the gate and get it looked at.
- Keypad or remotes quit working one at a time. Failures that creep in device by device usually trace back to the board or the receiver, not the devices. That’s a control problem, not a battery problem.
- The control enclosure is wet, corroded, or buzzing. Electrical faults at the enclosure are a job for a trained professional. Don’t open the panel and poke at it; get an electric gate specialist out.
Our Process, Step by Step
- 1
Phone consultation and brand check. We ask for the gate type, the brand if there is one, and what the gate is doing or not doing. That’s enough to know what the site visit needs to cover.
- 2
On-site measure and inspection. We measure the opening, check the slope and clearances, look at the existing power source, and note anything that will affect the install. No guessing from photos.
- 3
Written estimate. You get a clear scope and a price in writing before any work starts, with the gate, the operator, the controls, and the commissioning all accounted for. The written number is the price.
- 4
Install and commissioning. We set posts to proper footing depth, hang the gate, fit the operator, and wire the controls and safety devices. Then we test cycle after cycle with the safety devices live until the system runs clean.
- 5
Walk-through and handoff. We show you how the system operates, how to use the controls, and what to watch for. If anything turns up later, we’re the same team you call.
How Much Does Gate Installation Cost in Pittsburgh?
Gate installation in Pittsburgh is priced per job, and the range is wide because the variables are wide. A typical residential driveway gate with an operator in Pittsburgh runs $2,800 to $6,500 depending on width, material, and the operator class. A sliding gate setup with a cantilever and a matched operator runs $3,000 to $7,500. A straight operator install on an existing gate runs $1,400 to $4,000, and a custom-fabricated gate can run $2,500 to $8,000 or more. Commercial electric gate systems with access control sit higher, depending on the number of entry points and devices.
The price is driven by gate size and weight, the operator duty cycle, the power run distance, the number of access devices, and how much site work the footing and track need. A sloping driveway with a long power run on a hillside street is a different job from a flat drive with power already at the gate line, and the estimate reflects that.
To avoid overpaying, get the scope written before the work. Make sure the estimate covers the controls and the safety devices, not just the gate and the motor. Buy the operator sized for the gate, not the cheapest one on the pallet, since an undersized unit is what drives the repeat visits. Our estimate is free, the price is quoted and agreed before any work starts, and you’ll know what’s included before you commit. Call (866) 361-7838 for a written estimate.
Our Service Area Near Pittsburgh
We install and service gates across the Pittsburgh area, including Baldwin, Munhall, Wilkinsburg, Whitehall, West Mifflin, Bethel Park, Allison Park, McKeesport, and Jefferson Hills. Response times vary by location and by the scope of the job, and installation is scheduled after the on-site measure and written estimate. For urgent repair work, call and we’ll book the visit that fits. We answer 24/7.
Serving Pittsburgh, PA – Our Local Coverage Area
We serve Pittsburgh and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Installation in Pittsburgh
Gate installation is the full job of setting posts to proper footing depth, hanging the gate, fitting the operator, and wiring the controls and safety devices so the system works as one unit. It covers everything from the hole in the ground to the keypad on the post. Because we’re a gate specialist, the same team that installs also handles gate repair Pittsburgh work, so there’s no gap between the hardware and the electronics. Call (866) 361-7838 to get a measure on the books.
Most residential installations take a day or two on site, depending on the gate type, the site work, and whether the power run is ready. A custom fabrication adds lead time before the install day because the gate has to be built and finished first. Commercial systems with access control take longer because of the number of devices and the testing. The written estimate sets the expected timeline before work begins.
Gate installation in Pittsburgh typically runs $2,200 to $6,000 for a driveway gate, $3,000 to $7,500 for a sliding gate, and $3,500 to $8,000 for a full electric system with access control. The final number depends on gate size, operator class, the power run, and the devices. The written estimate sets the price and it’s quoted before work starts. Call (866) 361-7838 for an exact quote. Estimates are free.
Yes, we service FAAC and BFT systems and know where each one tends to fail first. We also work on Linear, Viking, LiftMaster, Ghost Controls, DoorKing, Elite, and Mighty Mule, so brand-specific diagnostics are part of every visit. Tell us the brand and the symptom when you call and we’ll come in already familiar with the equipment. Call (866) 361-7838 to book a visit.
Same-day service is available for repair work, and installation is scheduled after the on-site measure and written estimate. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. Call (866) 361-7838 to get on the schedule.
Warranty terms depend on the equipment and the scope of the job, and they’re set out in the written estimate before any work starts. Operator manufacturers carry their own warranties, and the estimate spells out what’s covered and for how long. We walk you through it at handoff so you know what to expect. Call (866) 361-7838 with questions about a specific scope.
Clear the work area, make sure the crew can get to the gate line, and have any existing gate hardware and controls accessible for the measure. If you know the brand and age of any existing operator, have that ready for the phone call. The on-site measure is where we check slope, clearances, and power, so there’s no prep beyond access. Call (866) 361-7838 to schedule the measure.
Schedule Your Gate Installation Service in Pittsburgh Today
A gate installation done right the first time saves you the repeat visits and the mid-winter failure. We measure the site, quote the whole scope in writing, and commit to that number before any work starts. If a Munhall or Pittsburgh property needs a gate that actually works in this climate, call (866) 361-7838 for a free, no-obligation estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Gate Repair Pittsburgh.